Case Project: Standard Biometric Analysis
1-Use the Internet and other sources to research the two disadvantages of standard biometrics: cost and error rates.
2-Select one standard biometric technique (fingerprint, Palm print, iris, facial features, etc) and research the costs for having biometric readers for that technique located at two separate entrances into a building.
3- Research ways in which attackers attempt to defeat this particular standard biometric technique.
4- How often will this technique reject authorized users while accepting unauthorized users compared to other standard biometric techniques?
5- Based on your research, would you recommend this technique? Why or why not?
Write all your findings in 1 to 2 pages, on word doc.

Answer:

Coiled tubing is often used to carry out operations similar to wire lining.

here's your answer..

Answer:The two-second rule is a rule of thumb by which a driver may maintain a safe trailing distance at any speed. The rule is that a driver should ideally stay at least two seconds behind any vehicle that is directly in front of his or her vehicle.

Explanation:

The number of tie-downs can be increased for extra safety. Therefore, it is essential to consult the FMCSA regulations and the manufacturer's guidelines to determine the appropriate number of tie-downs required for a 20-foot load. 150 words

The number of tie-downs required for a 20-foot load will depend on the type of cargo, the weight, the size, and the configuration of the vehicle, among other factors.

The Federal Motor Carrier Safety Administration (FMCSA) regulates the use of tie-downs to secure cargo on commercial motor vehicles. The FMCSA requires that all cargo be adequately secured to prevent shifting during transportation, especially on open trucks, flatbeds, and trailers. Therefore, the number of tie-downs will depend on the weight and type of cargo being transported. It is essential to note that the FMCSA has specific regulations and requirements for different types of cargo. For instance, FMCSA regulations require that a 20-foot load weighing less than 1,100 pounds may require at least one tie-down.

However, the rules can change depending on the length and weight of the load. For a 20-foot load weighing between 1,100 pounds and 2,200 pounds, two tie-downs are required. For loads weighing between 2,200 pounds and 5,000 pounds, the number of tie-downs required will depend on the length of the load and the type of cargo. In general, at least two tie-downs are required for cargo shorter than 5 feet, while longer cargo may require at least four tie-downs to secure the load.

Learn more about cargo:

https://brainly.com/question/31351351

#SPJ11

Answer:

What grade is this is for??

Focus primarily on highly precise specifics of what Cornell offers and how it matches with your interests and values. You can regard this as a "Why us?" essay with some optional "Why major" spice.

To learn more about essay refer :

https://brainly.com/question/94727

#SPJ4

Answer and Explanation:

Let A denote its switch first after that we will assume B which denotes the next switch and then we will assume C stand for both the bulb. we assume 0 mean turn off while 1 mean turn on, too. The light is off, as both switches are in the same place. This may be illustrated with the below table of truth:

A                    B                       C (output)

0                    0                        0

0                    1                          1

1                     0                         1

1                     1                          0

The logic circuit is shown below

C = A'B + AB'

If the switches are in multiple places the bulb outcome will be on on the other hand if another switches are all in the same place, the result of the bulb will be off. This gate is XOR. The gate is shown in the diagram adjoining below.

The code statements have a syntax error because "integer" is not a valid data type in most programming languages. I will assume that "integer" is meant to represent the "int" data type. Also, the capitalization of "Z" is incorrect.

Assuming these corrections, the correct code statements and the output will be:

int x = 34.54, y = 20, z = -5;

System.out.println(y > 50 && 2 > 10 || x > 30);

The output of this code will be:

true

Here's how the output is obtained:

The first expression y > 50 is false because y is 20, which is not greater than 50.

The second expression 2 > 10 is false because 2 is not greater than 10.

The third expression x > 30 is true because x is 34, which is greater than 30.

The && operator has higher precedence than the || operator, so the first two expressions are evaluated first. Since false && false is false, the third expression is evaluated next.

The expression false || true is true because at least one of the operands is true.

Therefore, the overall result of the expression is true.

TACACS+: A TCP-based access control protocol that enables a device to send a user's username and password to an authentication server in order to assess whether access is permitted.

If set up in this way, TACACS+ itself can function as an authentication server. Additionally, TACACS+ can offer services for accounting and authorization. The TACACS+ daemon is normally operating on a UNIX or Windows workstation, and TACACS+ services are kept up to date in a database on a server.

It offers distinct and modular facilities for authentication, authorization, and accounting. The TACACS+ daemon, a single access control server, enables autonomous provision of each service for authentication, authorization, and accounting. To benefit from various services offered on that server or on the Internet, each service can be connected to its own database.

Depending on the daemon's capabilities, a network. With the help of a single administration service, TACACS+ aims to offer a solution for managing numerous network access points.

1. Its architecture is client-server-based.

2. The Authentication Service (AS) and the Ticket Granting Service are implemented by the Kerberos server, also known as KDC (Key Distribution Cater) (TGS).

3. When a client communicates with an application server utilizing Kerberos tickets for authentication, the phrase "application server" normally refers to a Ferberized program. An example of an application server is the Kerberos telnet daemon (telnets).

4. Passwords are not transmitted over the network, in contrast to other authentication protocols (FTP, PAP, etc.) that do so.

To learn more about TACACS+ visit:

https://brainly.com/question/29770627

#SPJ4

Both technicians A and B are partially correct, because it's important to note that ABS is not a foolproof solution in all driving situations and should not be relied upon as a substitute for proper driving techniques and caution.Technician A is partially correct in that ABS (Anti-lock Braking System) can improve directional stability. Technician B is also partially correct in that ABS can improve braking performance on loose snow.

Both technicians are partially correct, but neither is entirely accurate.

Technician A is partially correct in that ABS (Anti-lock Braking System) can improve directional stability when the brakes are applied while turning a corner, especially on slippery or uneven road surfaces. The system can prevent the wheels from locking up and skidding, which can cause the vehicle to lose control. However, it's important to note that ABS does not necessarily guarantee superior directional stability in all situations, and the driver should still exercise caution and proper driving techniques when turning.

Technician B is also partially correct in that ABS can improve braking performance on loose snow, as the system can help prevent the wheels from locking up and losing traction. However, other factors such as tire type and condition, road gradient, and vehicle weight distribution can also impact braking performance on loose snow.

Therefore, both technicians are partially correct, but it's important to note that ABS is not a foolproof solution in all driving situations and should not be relied upon as a substitute for proper driving techniques and caution.

For such more questions on stability

https://brainly.com/question/1403056

#SPJ11

The bandwidth of a low-pass RL filter is the range of frequencies that can pass through the filter with minimal attenuation. It is defined as the difference between the upper and lower frequencies of the passband, where the attenuation is less than a certain threshold, usually -3 dB or half power point.

The cutoff frequency of a low-pass RL filter is the frequency at which the filter begins to attenuate the input signal. For a first-order low-pass RL filter, the cutoff frequency is given by the formulafc = R/(2πL)where R is the resistance of the series resistor and L is the inductance of the series inductor.If the cutoff frequency of a low-pass RL filter is 20 kHz, then we can calculate its bandwidth by determining the frequencies at which the filter's attenuation is -3 dB. Since the filter is a first-order low-pass filter, its attenuation at the cutoff frequency is -3 dB.

To learn more about bandwidth click on the link below:

brainly.com/question/30048853

#SPJ11

The property is that polyurethanes have a good tear resistance as well as tensile strength.

Polyurethane is an umbrella word for a group of polymers formed via the condensation of polyisocyanates and polyalcohols. Despite its xenobiotic origins, polyurethane has been discovered to be biodegradable by naturally occurring microbes.

Polyurethanes are synthesized by reacting a polyol (an alcohol having more than two reactive hydroxyl groups per molecule) with a diisocyanate or a polymeric isocyanate in the presence of appropriate catalysts and additives

To manage cell fate and tissue healing, biodegradable polyurethane platforms have been used. Cell bonding, spreading, multiplication, and separation are all influenced by framework features such as compound, mechanical, and primary. These are not fully fixed as the science of biodegradable polyurethanes, platform manufacturing technologies, and surface change approaches.

Learn more about polyurethane on:

https://brainly.com/question/2855921

#SPJ1

Answer:

Follows are the solution to this question:

Explanation:

Calculating the area under the curve:  

A = as

   \(=\frac{1}{2}(3 +6 \frac{m}{s^2})(100 \ m)+ \frac{1}{2}(6+4 \frac{m}{s^2})(100 m) \\\\=\frac{1}{2}(9 \frac{m}{s^2})(100 \ m)+ \frac{1}{2}(10\frac{m}{s^2})(100 m) \\\\=\frac{1}{2}(900 \frac{m^2}{s^2})+ \frac{1}{2}(1,000\frac{m^2}{s^2}) \\\\=(450 \frac{m^2}{s^2})+ (500\frac{m^2}{s^2}) \\\\= 950 \ \frac{m^2}{s^2}\)

Calculating the kinematics equation:

\(\to v^2 = v^2_{o} + 2as\\\\\)

        \(=0+ \sqrt{2as}\\\\ = \sqrt{2(A)}\\\\= \sqrt{2(950 \frac{m^2}{s^2})}\\\\= 43.59 \frac{m}{s}\)

Calculating the value of acceleration:  

\(\to a= \frac{dv}{dt}\)

\(=\frac{dv}{ds}(\frac{ds}{dt}) \\\\=v\frac{dv}{ds}\\\\\to \frac{dv}{ds}=\frac{a}{v}\)

\(\to \frac{dv}{ds} =\frac{4 \frac{m}{s^2}}{43.59 \frac{m}{s}} \\\\\)

         \(=\frac{0.092}{s}\)

Answer:

b. Gain management responsibilities

Explanation:

When you receive a vertical promotion, you are more likely to Gain management responsibilities  than when you receive a horizontal promotion.

The rooftop solar is a form of solar energy that can be installed on the roof of a home or business. It is cost-effective, environmentally friendly, and provides many benefits to homeowners and businesses.

The rooftop solar has many advantages over other forms of solar energy. One of the main advantages is that it provides 100% clean electricity from renewable sources. In addition, it can be combined with other sources such as wind power and geothermal power for even more benefits.

There are also many uses for rooftop solar panels in homes and businesses. One example is using it to heat water for hot water systems or heating swimming pools.

For me Bluebird Solar Private Limited is the best website in India for rooftop solar panels in India.

Answer:

Boring, since they would have the same personality, name, and occupation... it would be like doing the same thing every day or always talking to the same person. It would be impossible to figure out who is who since their looks would be the same as well. Although they might be fun to hang around with them if they had the same humor as you, or liked doing the same activities.

Explanation:

hope this helps:)

A group of friends that are identical in every manner would prevent opportunities for personal development and learning, but having friends with similar interests and values might foster a feeling of community and shared experiences.

Thus, Lack of diversity would limit opportunities for new viewpoints, original ideas, and varied experiences. There might not be enough intellectual and emotional stimulation and repetitious conversations and exchanges.

Because everyone would address problems and obstacles in the same way, life might become predictable and static.

Although conflicts and disagreements may be less frequent, the lack of diverse opinions may make it more difficult to come up with original solutions.

Thus, A group of friends that are identical in every manner would prevent opportunities for personal development and learning, but having friends with similar interests and values might foster a feeling of community and shared experiences.

Learn more about Learning, refer to the link:

https://brainly.com/question/1503472

#SPJ3

Answer:

nsnsndndnndndndnhhhh

The correct answer is  Valve clearance is not typically part of the check of the engine compartment done for a pre-trip inspection.

The other items you mentioned, such as engine oil level, condition of belts and hoses, and worn wiring insulation, are commonly included in a pre-trip inspection of the engine compartment.Engine oil level: This is a check to ensure that there is sufficient engine oil to lubricate the engine and that it is at the correct level.Coolant level: This is a check to ensure that there is sufficient coolant to maintain the engine at a safe operating temperature.Belts and hoses:

To learn more about Valve click the link below:

brainly.com/question/24417556

#SPJ11

Here is the ER diagram for the Cruise Business Case:

+-------------+          +-------------+

|   Employee  |          |    Ships    |

+-------------+          +-------------+

| EmployeeID  |          |   ShipID    |

| LastName    |          | ShipName    |

| FirstName   |          | Description |

| Type        |          +-------------+

| ParrotID    |<---------|     Crew    |

+-------------+          +-------------+

                         |   Captain   |

                         |  ParrotID   |

                         +-------------+

+--------------+         +--------------+

|   Parrot     |         |  Dependents  |

+--------------+         +--------------+

| ParrotID     |<--------|  DependentID |

| ParrotName   |         |  FirstName   |

| Color        |         |  EmployeeID  |

+--------------+         +--------------+

+--------------+         +-------------+

|   Missions   |         | MissionShip |

+--------------+         +-------------+

| MissionID    |         | MissionID   |

| MissionName  |         | ShipID      |

| ScheduledDate|         +-------------+

| QuotedPrice  |

+--------------+

The tables and their relationships are as follows:

Learn more about ER diagram at:

https://brainly.com/question/30710118

#SPJ1

Answer:

yes it is very hard you should find a reccomended doctor to aid in your situation. But in the meantime how about you give me that lil brainliest thingy :p

Answer:

Super critical

1.2 m

Explanation:

Q = Flow rate = \(12\ \text{m}^3/\text{s}\)

w = Width = 3 m

d = Depth = 90 cm = 0.9 m

A = Area = wd

v = Velocity

g = Acceleration due to gravity = \(9.81\ \text{m/s}^2\)

\(Q=Av\\\Rightarrow v=\dfrac{Q}{wd}\\\Rightarrow v=\dfrac{12}{3\times 0.9}\\\Rightarrow v=4.44\ \text{m/s}\)

Froude number is given by

\(Fr=\dfrac{v}{\sqrt{gd}}\\\Rightarrow Fr=\dfrac{4.44}{\sqrt{9.81\times 0.9}}\\\Rightarrow F_r=1.5\)

Since \(F_r>1\) the flow is super critical.

Flow is critical when \(Fr=1\)

Depth is given by

\(d=(\dfrac{Q^2}{gw^2})^{\dfrac{1}{3}}\\\Rightarrow d=(\dfrac{12^2}{9.81\times 3^2})^{\dfrac{1}{3}}\\\Rightarrow d=1.2\ \text{m}\)

The depth of the channel will be 1.2 m for critical flow.

Matter can be defined as anything (physical object or body) that has mass and takes up space. Thus, the mass of a physical object measures the amount of matter the object contains.

In Science, water is an example of matter and it exists in three (3) main states or phases such as the following:

Based on scientific records and information, we know that all particles have various degrees of attraction to one another and this can be described as follows:

Read more on matter here: https://brainly.com/question/24783543

#SPJ1

Complete Question:

A student is investigating the particles in a glass window, raindrops on the window, and the air around the window. Assume the window, raindrops, and the air are all at 25 degrees Celsius. Identify the particle structure in each sample of matter.

Answer:people tend to do this when they are in a different environment they lose something or just have something going on in their life

Explanation:

The types of materials are best for preventing heat transfer through convection include the following:

In Science, there are three (3) main types of heat energy transmission and these include the following:

Convection can be defined as a heat energy transfer process which typically involves the transfer of heat, as a result of the movement of mass.

Based on scientific research and experiments, convection is generally considered to be a more effective and efficient means of heat transport on planet Earth when compared to conduction.

Read more on heat here: brainly.com/question/12072129

#SPJ1

The technique of adjusting the spaces between words to add more characters in a line is called justification, while the technique of adjusting the spaces between specific character pairs to improve readability is called kerning.

Justification is commonly used in publishing, where it is important to have evenly spaced lines of text. Kerning is used to make sure that certain character combinations, such as "WA" or "To", do not have too much or too little space between them, which can affect the overall readability of the text.

Both techniques are important in typesetting and can significantly improve the overall appearance and legibility of printed or digital text.

To know more about kerning visit:

https://brainly.com/question/16937802

#SPJ11

Answer:

a) 75%

b) 82%

Explanation:

Assumptions:

\(\text{The mechanical energy for water at turbine exit is negligible.} \\ \\ \text{The elevation of the lake remains constant.}\)

Properties: The density of water \(\delta = 1000 kg/m^3\)

Conversions:

\(165 \ ft \ to \ meters = 50 m \\ \\7000 \ lbm/s \ to \ kilogram/sec = 3175 kg/s \\ \\1564 \ hp \ to \ kilowatt = 1166 kw \\ \\\)

Analysis:

Note that the bottom of the lake is the reference level. The potential energy of water at the surface becomes gh. Consider that kinetic energy of water at the lake surface & the turbine exit is negligible and the pressure at both locations is the atmospheric pressure and change in the mechanical energy of water between lake surface & turbine exit are:

\(e_{mech_{in}} - e_{mech_{out}} = gh - 0\)

Then;

\(gh = (9.8 m/s^2) (50 m) \times \dfrac{1 \ kJ/kg}{1000 m^2/s^2}\)

gh = 0.491 kJ/kg

\(\Delta E_{mech \ fluid} = m(e_{mech_{in}} - e_{mech_{out}} ) \\ \\ = 3175 kg/s \times 0.491 kJ/kg\)

= 1559 kW

Therefore; the overall efficiency is:

\(\eta _{overall} = \eta_{turbine- generator} = \dfrac{W_{elect\ out}}{\Delta E_{mech \fluid}}\)

\(= \dfrac{1166 \ kW}{1559 \ kW}\)

= 0.75

= 75%

b) mechanical efficiency of the turbine:

\(\eta_{turbine- generator} = \eta_{turbine}\times \eta_{generator}\)

thus;

\(\eta_{turbine} = \dfrac{\eta_{[turbine- generator]} }{\eta_{generator}} \\ \\ \eta_{turbine} = \dfrac{0.75}{0.92} \\ \\ \eta_{turbine} = 0.82 \\ \\ \eta_{turbine} = 82\%\)

Answer:

PF= .54

Explanation:

Power Factor equals working/real power (W) over apparent power (VA). 1.0 PF is an efficient equipment. PF= 22/(120*.34)

The power factor of the ballast is 0.54 which is the ratio of working power to apparent power.

The power factor is a measure of energy efficiency. It is typically expressed as a percentage, with a lower percentage indicating inefficient power usage.

The power factor (PF) is the ratio of working power (in kW) to apparent power (in kilovolt amperes) (kVA).

Given that a 120-volt fluorescent ballast has an input current of 0.34 ampere and an input power rating of 22 watts.

PF = (True power)/(Apparent power)

PF = W/VA

Here W = 22 watts, V = 120-volt, and A = 0.34 ampere

PF = 22 / (120 × 0.34)

PF = 22 / 40.8

PF = 0.5392

PF = 0.54

Thus, the power factor of the ballast is 0.54.

Learn more about the power factor here:

https://brainly.com/question/19567608

#SPJ2

Answer:

The five stages of Design Thinking, according to d.school, are as follows: Empathise, Define , Ideate, Prototype, and Test. Let's take a closer look at the five different stages of Design Thinking

Explanation:

Answer:

make sure its safe make sure it works as inteded

Explanation:

yes