Utilizing color picker tools, color charts, and HTML color names with Hex, RGB, and HSL values will simplify the process of finding the right color codes for your website.
A color picker tool allows you to select a color visually, and it will provide you with the corresponding HTML color code. A color chart is a pre-defined set of colors with their respective color codes, making it simple to choose a color and obtain its code. HTML color names are a list of standard color names that web browsers recognize, which come with Hex, RGB, and HSL values. Hex color codes represent colors using six-digit hexadecimal values, while RGB and HSL values represent colors in Red-Green-Blue and Hue-Saturation-Lightness formats, respectively.
To know more about HTML visit:
https://brainly.com/question/24065854
#SPJ11
which statement best describes the velocity of a bus traveling along its route
Answer:
Option A is the correct answer. The bus traveled at 50 mph for 20 minutes
Explanation:
The complete question is
Which of the following choices best describes velocity of a bus traveling along its route? A. The bus traveled at 50 mph for 20 minutes. B. The airplane traveled southwest at 280 mph. C. The car went from 35 mph to 45 mph. D. The train made several stops, with an average rate of 57 mph.
Solution
In option A the bus is travelling at a speed of 50 miles per hour. This describes the velocity of bus along its route.
The other options are about the velocity of airplane, car and train
how long in minutes would it take to fabricate a 4 colored ball in diameter using fdm? assume a layer thickness of , a width of , and the extrudate being deposited at a rate of . the stage movement time is per layer, and it takes to switch between any two materials. assume the support structure has a volumetric fill ratio of .
FDM is a manufacturing process that creates objects layer by layer by depositing molten thermoplastic material.
The length of time it takes to create a four-colored ball with a diameter using FDM is determined by a variety of variables.
These variables are layer thickness, nozzle width, extrudate deposition rate, stage movement time per layer, and the time it takes to change between any two materials.
The ball's construction time can be calculated using these variables.
The following formula can be used to calculate the ball's production time:
Volume of Sphere = 4/3 * pi * r³
Volume of the sphere = 4/3 x pi x 2²³
Volume of the sphere = 33.51 cm³
The total volume of the ball will be 33.51 cm³.
We'll use this to figure out how long it will take to manufacture this ball.
We can use the following formula:
Time = (Layer height x Layer width x 60) / Extrudate Deposition Rate x Stage Movement Time x Fill ratio x Volume of sphere
Time = (0.15 x 0.4 x 60) / 6 x 1 x 0.3 x 33.51The time it takes to fabricate the ball is calculated as follows:
Time = 5.13 hours or 308 minutes
it will take around 308 minutes to fabricate a 4 colored ball in diameter using FDM,
assuming a layer thickness of 0.15mm, a width of 0.4mm, and the extrudate being deposited at a rate of 6 cubic mm per second.
Additionally, it is supposed that the stage movement time is 1 minute per layer, and it takes 1 minute to switch between any two materials.
Finally, assume the support structure has a volumetric fill ratio of 30%.
To know more about thermoplastic visit:
https://brainly.com/question/33512414
#SPJ11
Which tool should an analyst in engineering design for the given scenario?
Answer:
What are some types of analysis that an engineer could use to test a design? (Possible answers may relate to: mathematical calculations; testing of stress, loads or function; or computer-aided analysis.)
hope it helps you..✌️
Answer:
\({\large{\pink{ \overline{ \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: \: }}}}{}\ _{ \red{ \heartsuit}} \)
Consider the signal x(t) = e-5tu(t -1), and denote its Laplace transform by X(s). (a) Using eq. (9.3), evaluate X(s) and specify its region of convergence. (b) Determine the values of the finite numbers A and to such that the Laplace transform G(s) of g(t) = Ae-51 u(-t-to) has the same algebraic form as X(s). What is the region of convergence corresponding to G(s)?
The region of convergence corresponding to G(s) will be To = -1 and A = 1
How to illustrate the information?Based on the information given, it should be noted that the value when we evaluate X(s) and specify its region of convergence will be:
X(s( = e^(5 + 5)/(5+5)
= -5.
The region where the function exists in the transfer function's pole/zero plot is known as the Region of Convergence. We prefer to deal with rational functions for the purpose of practical filter design, which may be defined by two polynomials, one for identifying the poles and the other for calculating the zeros, respectively.
The values of the finite numbers A and to such that the Laplace transform G(s) of g(t) = Ae-51 u(-t-to) has the same algebraic form as X(s) will be - 1 and the region of convergence corresponding to G(s) is 1.
Therefore based on the information, the region of convergence corresponding to G(s) will be To = -1 and A = 1.
Learn more about convergence on:
brainly.com/question/1521191
#SPJ1
A benefit to using the medium the author used in "Great Rock and Roll
Pauses" is that the audience:
Incomplete question. The options read;
A. can change the story's ending
B. listens to the dialogue
C. hears the rock songs
D. feels more connected to the text.
Answer:
D. feels more connected to the text.
Explanation:
Remember, the underlying motive of an author when writing any text is to make his readers or audience more connected to the material been read or heard.
Hence, in "Great Rock and Roll Pauses" we can conclude that the author's choice of medium was motivated by the same desire of making the audience feel more connected to the text.
Answer:
The audience can actually hear the music.
Explanation: dont listen to below average iq people :0
A city is experiencing a windstorm. The wind has blown away some of the houses in that city. What load bearing factor did the architects of these
houses not calculate correctly?
OA material strength
OB. elasticity
oc design load
OD. safety factor
Answer:
oa
Explanation:
Answer:
safety factor
Explanation:
i got it correct on the test
6 A series of vane shear tests has been performed in a stratum of inorganic clay that has a plasticity index of 50. The vane had a diameter of 50 mm and a height of 100 mm. The test results were as follows: Depth (m) Torque at Failure (N-m) 3.4 12.7 4.1 18.1 5.0 15.8 6.6 20.1 Compute the undrained shear strength, su, for each test, then combine this data to determine a single su value for this stratum.
The UHRS platform is optimized for Edge/Internet Explorer only. You can still use your favorite browser, but keep in mind that you may experience technical issues when working on UHRS with a different browser than Edge or Internet Explorer.
UHRS is optimized for...
It is to be noted that all UHRS platforms are optimized for the popular kinds of internet browser applications.
What is a UHRS?The Universal Human Relevance System (UHRS) is a crowdsourcing platform that allows for data labeling for a variety of AI application situations.
Vendor partners link people referred to as "judges" to offer data labeling at scale for us. All UHRS judges are bound by an NDA, ensuring that data is kept protected.
A browser is a software tool that allows you to see and interact with all of the knowledgeon the World Wide Web. Web sites, movies, and photos are all examples of this.
Learn more about internet browser applications.:
https://brainly.com/question/16829947
#SPJ1
IV. An annealed copper strip 9 inches wide and 2.2 inches thick, is rolled to its maximum possible draft in one pass. The following properties of annealed copper are given: strength coefficient is 90,000 psi; true strain at the onset of non-uniform deformation is 0.45; and, engineering strain at yield is 0.11. The coefficient of friction between strip and roll is 0.2. The roll radius is 14inches and the rolls rotate at 150 rpm. Calculate the roll-strip contact length. Calculate the absolute value of thetrue strain that the strip undergoes in this operation. Determine the average true stress of the strip in theroll gap. Calculate the roll force. Calculate the horsepower required.
Answer:
13.9357 horse power
Explanation:
Annealed copper
Given :
Width, b = 9 inches
Thickness, \($h_0=2.2$\) inches
K= 90,000 Psi
μ = 0.2, R = 14 inches, N = 150 rpm
For the maximum possible draft in one pass,
\($\Delta h = H_0-h_f=\mu^2R$\)
\($=0.2^2 \times 14 = 0.56$\) inches
\($h_f = 2.2 - 0.56$\)
= 1.64 inches
Roll strip contact length (L) = \($\sqrt{R(h_0-h_f)}$\)
\($=\sqrt{14 \times 0.56}$\)
= 2.8 inches
Absolute value of true strain, \($\epsilon_T$\)
\($\epsilon_T=\ln \left(\frac{2.2}{1.64}\right) = 0.2937$\)
Average true stress, \($\overline{\gamma}=\frac{K\sum_f}{1+n}= 31305.56$\) Psi
Roll force, \($L \times b \times \overline{\gamma} = 2.8 \times 9 \times 31305.56$\)
= 788,900 lb
For SI units,
Power = \($\frac{2 \pi FLN}{60}$\)
\($=\frac{2 \pi 788900\times 2.8\times 150}{60\times 44.25\times 12}$\)
= 10399.81168 W
Horse power = 13.9357
What relates a landscape architect's knowledge of design to the landscape architect's knowledge of law and government?
Answer:
The landscape architect uses knowledge of legal requirements to inform design choices.
Explanation:
The landscape architect doesn’t only draw on knowledge of law and government to design grounds for public buildings, but will draw on that knowledge quite often on many projects. The landscape architect’s knowledge of design is not purely intuitive but is a product of study and might involve research. The landscape architect’s knowledge of law and government, however, does come into play in making design choices that are consistent with the law and government regulations.
6.A tape measure is used
A. in manufacturing industries
B. in construction industries
C. for precision measurement
D. A and B
What might be in the ethanol/aqueous interface? How could you eliminate this?
The ethanol-aqueous interface typically contains impurities such as surfactants, soluble organic and inorganic compounds, and other contaminants. Impurities such as this can affect the quality and purity of the final product. There are various ways to remove this interface.
One of them is by using a centrifuge. It can be used to physically remove the interface by spinning the mixture at high speeds. This separates the ethanol and aqueous layers, making it easier to eliminate the interface.Another option is to use a decanter. It is a device that separates liquids with different densities. It can be used to remove the ethanol-aqueous interface by gravity separation.The most effective way of eliminating impurities in the ethanol-aqueous interface is through distillation. It separates the impurities from the ethanol, resulting in a pure ethanol product. This is done by heating the mixture to the boiling point of ethanol. The ethanol vapor is then condensed into a separate container, leaving behind the impurities in the original container.There are several ways to eliminate the ethanol-aqueous interface, but the method you choose will depend on the amount and type of impurities present, as well as the desired purity of the final product.
To know more about contaminants, visit:
https://brainly.com/question/28328202
#SPJ11
Where do greywater pipes generally feed into?
-Vent stack
-Water heater
-Waste stack
-Main supply
Answer:
c Waste stack
Explanation:
The seven P's adds _____.
The seven P's adds people , place , physical and process. Moreover, these seven elements comprise the marketing mix.
What are the seven Ps?Every part of your marketing strategy can benefit from using the 7Ps of marketing. To ensure that you are conveying a coherent and consistent message about your business and brand, you should take into account the product, price, location, promotion, people, process, and physical evidence holistically.
Why are the 7 Ps important?The 7Ps help businesses examine and define key issues that influence product and service marketing. The marketing mix, also known as the 7Ps framework for the digital marketing mix, which is a well-liked marketing model.
Learn more about 7 p's:
brainly.com/question/15583880
#SPJ1
A 1020 Cold-Drawn steel shaft is to transmit 20 hp while rotating at 1750 rpm. Calculate the transmitted torque in lbs. in. Ignore the effect of friction.If the shaft in Q2 was made of ASTM 30 cast iron, what would be the factor of safety
Answer:
Question 1 A 1020 Cold-Drawn steel shaft is to transmit 20 hp while rotating at 1750 rpm. Calculate the transmitted torque in lbs. in. Ignore the effect of friction. Answer with three decimal points. 60.024 Question 2 Based on the maximum-shear-stress theory, determine the minimum diameter in inches for the shaft in Q1 to provide a safety factor of 3. Assume Sy = 57 Kpsi. Answer with three decimal points. 0.728 Question 3 If the shaft in Q2 was made of ASTM 30 cast iron, what would be the factor of safety? Assume Sut = 31 Kpsi, Suc = 109 Kpsi 0 2.1 O 2.0 O 2.5 0 2.4 2.3 O 2.2
Explanation:
hope it helps
What observation can you notice in transferring heat by changing the intermediate section
material with a different cross-sectional area?
The observation that will be noticed in transferring heat by changing the intermediate cross sectional area is that;
An increase in the intermediate cross sectional area would lead to an increase in the rate of heat transfer and vice versa.
According to fourier's equation for heat conduction, the rate of heat transfer is given by the equation;dQ/dt = kA(dT/dx)
Where;
dQ/dt is rate of heat transfer
k is thermal conductivity of the medium
A is cross sectional area
dT/dx is the rate of change of the temperature per unit length
Now, from the above equation, we can see that the rate of heat transfer is directly proportional to the cross sectional area of the material through which the heat is being conducted. This means that the wider the cross sectional area, the more the surface particles required to conduct heat and definitely the higher the rate of heat transfer.Read more at; https://brainly.com/question/13051858
consider a solid circular cylinder with 100 mm length and 20 mm radius subjected to 1x106 nmm torque. the cylinder is made up of a linearly elastic material with shear modulus 10gpa. calculate a) polar moment f inertia b) the maximum shear stress in mpa c) the maximum shear strain
Question: Consider a solid circular cylinder with 100 mm length and 20 mm radius subjected to 1x106 nmm torque. The cylinder is made up of a linearly elastic material with shear modulus 10GPA. Calculate a) Polar Moment of Inertia, b) Maximum Shear Stress in MPa, c) Maximum Shear Strain.
Answer:
a) Polar Moment of Inertia can be calculated using the formula: I = (1/2) πr4.
For a solid circular cylinder with a radius of 20mm, the Polar Moment of Inertia would be 50,265.
b) Maximum Shear Stress can be calculated using the formula: τmax = T/J, where T is the applied torque and J is the Polar Moment of Inertia.
For this cylinder, the Maximum Shear Stress would be 19.84 MPa.
c) Maximum Shear Strain can be calculated using the formula: ε = τ/G, where τ is the maximum shear stress and G is the shear modulus.
For this cylinder, the Maximum Shear Strain would be 1.984.
To learn more about this visit - Maximum shear stress maximum shear strain : https://brainly.com/question/12993472
#SPJ11
The following incomplete method is intended to sort its array parameter arr in increasing order.
// postcondition: arr is sorted in increasing order
public static void sortArray(int[] arr)
{
int j, k;
for (j = arr.length - 1; j > 0; j--)
{
int pos = j;
for ( /* missing code */ )
{
if (arr[k] > arr[pos])
{
pos = k;
}
}
swap(arr, j, pos);
}
}
Assume that swap(arr, j, pos) exchanges the values of arr[j] and arr[pos]. Which of the following could be used to replace /* missing code */ so that executing the code segment sorts the values in array arr?
A
k = j - 1; k > 0; k--
B
k = j - 1; k >= 0; k--
C
k = 1; k < arr.length; k++
D
k = 1; k > arr.length; k++
E
k = 0; k <= arr.length; k++
As it meets the criteria for looping through the unsorted portion of the array and iterating from the first unsorted element up to the current value of j, k = 1; k arr. length; k++.
How can I determine how many elements there are in an unsorted array?We must do a linear search to locate the largest value in an unsorted array by examining each element and keeping note of the location the maximum has been discovered thus far.
Which approach requires the least amount of time to search an entry in an unsorted array?The most popular method of searching an element in an unsorted array is by performing a linear search, which checks each element one by one from start to finish and has an O(n) complexity.
To know more about looping visit:-
https://brainly.com/question/30706582
#SPJ1
True or false
Consumer is the end user
Client is usually a company
Consumer is usually a company
Client is the end user
Consumer is the end user
Client is usually a company
Consumer is usually a company
Client is the end user
Answer:
Explanation:
a) True
b) False
c) False
d) False
e) True
f) False
g) False
h)False
Plz mark as brainliest
what is the most common type of suspensions system used on body over frame vehicles?
Answer:
Engine
Explanation:
Semi-independent suspension is the most common type of suspension system used on body over frame vehicles.
What is a Semi-independent suspension?Semi-independent suspension give the front wheels some individual movement.
This suspension only used in rear wheels.
Thus, the correct option is Semi-independent suspension
Learn more about Semi-independent suspension
https://brainly.com/question/23838001
#SPJ2
The force that your engine applies to turn your cars wheels
if the height of a 12 in. wide rectangular beam section is increased from 16 in. to 32 in. (i.e., initial section is 12x16 in. and final section is 12x32 in.), the maximum flexure or bending stress in the beam becomes?
The maximum flexure or bending stress in the beam is increased by a factor of 4.
The maximum flexure or bending stress in a beam is calculated using the equation:
σ = Mc/I
Where,
σ = Maximum flexure or bending stress (MPa)
M = Maximum bending moment (N.m)
c = Distance from Neutral Axis to outermost fibre (mm)
I = Moment of Inertia (mm4)
For the given beam,
Initial Section: 12 x 16 in.
Final Section: 12 x 32 in.
For the initial section:
I1 = b1 x h12^3/12 = 12 x 162^3/12 = 24576 in4
For the final section:
I2 = b2 x h22^3/12 = 12 x 322^3/12 = 98304 in4
Therefore, the Moment of Inertia (I) is increased by a factor of 4 (I2 = 4 x I1).
Since M and c remain unchanged, the maximum flexure or bending stress (σ) is increased by a factor of 4 (σ2 = 4 x σ1).
For more questions like Flexure click the link below:
https://brainly.com/question/29892776
#SPJ4
Hey guys can anyone list chemical engineering advancement that has been discovered within the past 20 years
Meredith implements a "graph coloring" algorithm, which comes up with colors for graph vertices such that no neighboring vertices share the same color.
The algorithm outputs graph colorings like this one:
Using a palette of just 3 colors, she runs the algorithm on graphs with varying amounts of vertices and records how long it takes.
Her findings are summarized in this table:
Graph vertices Steps
4 81
6 729
8 6561
Based on the table, which of the following statements describe the run time for this algorithm?
????️Note that there are 2 answers to this question.
The process of giving different colors to each vertex of a graph G so that no two neighboring vertices receive the same color is known as graph coloring.
What is Graph coloring algorithm?When coloring a graph, the goal is to use as few colors as possible. The chromatic number of a graph G is the lowest set of colors needed to color that graph. A NP Complete problem is the graph coloring issue.
A unique characteristic of a graph coloring is that two neighboring vertices, or those with an edge connecting them, cannot have the same color.
The difficulty stems from the fact that two countries (or states) must have distinct colors when they are close to one another when coloring a map. The United States is depicted on the following four-color map.
Therefore, The process of giving different colors to each vertex of a graph G so that no two neighboring vertices receive the same color is known as graph coloring.
To learn more about Algorithm, refer to the link:
https://brainly.com/question/22984934
#SPJ1
Crude oil at 20 c fills the space between two concentric cylinders 250 mm high and with diameters of 150 mm and 156 mm. Find the torque is required to rotate the inner cylinder at 12 r min, the outer cylinder rernaining stationary
the torque is required to rotate the inner cylinder at 12 r min, the outer cylinder remaining stationary is 11.0807 N-m.
we have left out some other important details, such as the time required to reach that rpm, whether the beginning state is at rest, and the axis around which the cylinder is revolving. However, we'll suppose that it will be 60 seconds (time is necessary to convert rpm to angular acceleration)
rotation around the center axis
Angular acceleration = torque + MOI
Currently, angular acceleration equals 2 rpm/(t 60).
In order to avoid getting an extremely high figure, we estimated that the diameter of the cylinder was 600 mm rather than 600 meters: angular acceleration= 1.047 rad/s² MOI for cylinder across center dia= 1/4MR²+ 1/12ML²
MOI= 10.5833 kg-m
Now, the product of these two is torque.
11.0807 N-m of torque
Various MOI equations can be used to compute for different axes of rotation.
Learn more about Acceleration here-
https://brainly.com/question/12550364
#SPJ4
The complete question is:
Crude oil at 20 c fills the space between two concentric cylinders 250 mm high and with diameters of 150 mm and 156 mm. Find the torque is required to rotate the inner cylinder at 12 r min, the outer cylinder remaining stationary.
The cross section of a river may be idealized as shown below. Find the discharge carried by the river if S=2*10-4 for all sections. The side slope at both sides is 1:1
Answer:
Explanation:
To find the discharge carried by the river, we need to use the cross-sectional area of the river and the velocity of the water. The cross-sectional area can be found by integrating the width of the river across the depth.If the side slope of the river is 1:1, that means that for every 1 meter of horizontal distance from the centerline, the depth of the water decreases by 1 meter. Using this information, we can set up the following integral to find the cross-sectional area:A = ∫[0,b] (b - x) dxWhere b is the width of the river at the base, and x is the distance from the centerline.Solving this integral, we find that the cross-sectional area is:A = (b^2)/2Now that we have the cross-sectional area, we can use the equation for discharge:Q = VAWhere Q is the discharge, V is the velocity of the water, and A is the cross-sectional area. If S is equal to 210^-4 for all sections, that means that the slope of the river is 210^-4. The velocity of the water can be found using the equation:V = √(SgD)Where S is the slope of the river, g is the acceleration due to gravity (9.81 m/s^2), and D is the depth of the water.If we plug in the values for S, g, and D, we can find the velocity of the water and then use the equation for discharge to find the total discharge carried by the river.For example, if the width of the river at the base is 10 meters and the depth of the water is 5 meters, the cross-sectional area would be:A = (10^2)/2 = 50 m^2The velocity of the water would be:V = √(2*10^-4 * 9.81 * 5) = 1.99 m/sAnd the discharge would be:Q = VA = 50 m^2 * 1.99 m/s = 99.5 m^3/sThis is the total discharge carried by the river.
Determine the maximum deflection of the solid circular shaft. The shaft is made out of steel E=200 GPa. It has a diameter of 100 mm.
a) 1.27 mm
b) 2.54 mm
c) 5.08 mm
d) 10.16 mm
To determine the maximum deflection of a solid circular shaft, we can use the formula for deflection in a circular beam under bending:
δ = (F * L^3) / (3 * E * I)
Where:
δ is the maximum deflection,
F is the applied force,
L is the length of the shaft,
E is the modulus of elasticity (Young's modulus),
I is the area moment of inertia.
In this case, we are given the diameter of the shaft, which we can use to calculate the area moment of inertia:
I = (π/64) * d^4
Where d is the diameter of the shaft.
Given:
E = 200 GPa = 200 * 10^9 Pa
d = 100 mm = 0.1 m
Substituting the values into the formula, we have: δ = (F * L^3) / (3 * E * I)
= (F * L^3) / (3 * E * ((π/64) * d^4))
Since we are not given the applied force or length of the shaft, we cannot calculate the exact deflection. The maximum deflection will depend on the specific loading conditions and dimensions of the shaft.
Therefore, we cannot determine the maximum deflection of the solid circular shaft with the given information. None of the provided options (a, b, c, d) can be considered as the correct answer.
To know more about maximum deflection visit:
https://brainly.com/question/18688482
#SPJ11
pda for the set of all strings of o's and 1 's such that no prefix has more 1 's than o's.
Answer:
Explanation:
A pushdown automaton (PDA) can be designed to recognize the set of all strings consisting of '0's and '1's such that no prefix has more '1's than '0's. The PDA can be represented as:
Q: Set of states
Σ: Input alphabet {0, 1}
Γ: Stack alphabet {0, 1, $}
δ: Transition function
q0: Initial state
Z: Initial stack symbol
The PDA transitions can be defined as follows:
1. Start in state q0 with Z on the stack.
2. Read the input symbol:
a. If it is '0', transition to a new state while leaving the stack unchanged.
b. If it is '1':
i. If the top symbol of the stack is '1', transition to a reject state.
ii. If the top symbol is '0' or the stack is empty, transition to a new state by pushing '1' onto the stack.
3. Repeat steps 2 until all input symbols are processed.
4. If the input is fully consumed and the stack is empty, transition to an accept state. Otherwise, transition to a reject state.
This PDA ensures that at no point during the input processing does the stack contain more '1's than '0's, satisfying the condition of no prefix having more '1's than '0's.
Learn more about pushdown automata and their applications in recognizing language patterns.
https://brainly.in/question/6340371
#SPJ11
.Which of the following non-digital data storage items is most similar to a database?
A) library card catalog
B) cash register receipt
C) doctor's office invoice
D) list of sales totals on a spreadsheet
The non-digital data storage item most similar to a database among the given options is A) library card catalog.
A library card catalog is an organized system for tracking the books and materials available in a library. It functions as a database because it stores and categorizes data, making it easy to search and retrieve information about the library's resources. Just like a digital database, a card catalog contains structured data with a specific set of fields (such as title, author, and publication date) for each entry. This enables users to search for and locate the desired materials efficiently.
The other options, such as cash register receipts (B) and doctor's office invoices (C), do store data but lack the systematic organization and searchability of a database. Option D, a list of sales totals on a spreadsheet, is closer to a database but still lacks the extensive organization and search capabilities typically associated with a database.
To know more about non-digital data storage visit:
https://brainly.com/question/28385898
#SPJ11
A coil consists of 200 turns of copper wire and have a cross-sectional area of 0.8 mmm square.The mean length per turn is 80 cm and the resistivity of copper is 0.02μΩm at normal working temperature.Calculate the resistance of the coil
Answer:
The resistance of the coil is 4 Ω.
Explanation:
The resistance (R) of the coil can be calculated using the following equation:
\(R = \frac{\rho L}{A}\)
Where:
ρ: is the resistivity of copper = 0.02x10⁻⁶ Ωm
L: is the length of the coil
A: is the cross-sectional area = 0.8 mm² = 8x10⁻⁷ m²
The length of the coil is given by:
\( L = 200 turn* 80 cm/turn = 16000 cm = 160 m \)
Now, the resistance is:
\(R = \frac{\rho L}{A} = \frac{0.02 \cdot 10^{-6} \Omega m*160 m}{8 \cdot 10^{-7} m^{2}} = 4 \Omega\)
Therefore, the resistance of the coil is 4 Ω.
I hope it helps you!