Review the first capture file (Project Part I-a) and determine what is happening with the HTTP traffic.
Project part 1-a.pcap
Describe the traffic: what packets are involved and what is happening? (include source, destination, time of capture)
Take a screenshot of the actual packets within the capture file that you observed this behavior.

Answer:

Zoning is like a hammer because it is used as a tool for urban planning.

The magnitude of the e.m.f induced in one coil when the current in the other is increasing at a rate of 40 A/s is 6.8 V.

Mutual inductance is a property of two coils that are in close proximity to each other. It measures the amount of magnetic flux that is linked between the two coils. The mutual inductance between two coils is denoted by the symbol M and is measured in henries (H).

According to Faraday's law of electromagnetic induction, an e.m.f is induced in a coil whenever there is a change in the magnetic flux that links the coil. The magnitude of the induced e.m.f is given by the formula:
e = -M(dI/dt)
where e is the induced e.m.f, M is the mutual inductance, and dI/dt is the rate of change of current in the other coil.
Substituting the given values, we get:
e = -170 x 10^-3 H x (40 A/s) = -6.8 V

To know more about current  visit:-

https://brainly.com/question/31834315

#SPJ11

2.56% benzene, 53.8% toluene, and 43.6% xylene make up the molar composition of the bottom stream from the second column.

The first step in resolving this issue is to determine the moles of benzene, toluene, and xylene in the top stream from the first column, followed by determining the moles of toluene and xylene in the top stream from the second column.

Benzene moles in the first column's top stream are equal to 0.225 moles (0.75 * 0.30).

0.35 * 0.30 = 0.105 moles of toluene in the top stream of the first column.

Moles of xylene in the first column's top stream are calculated as follows: 0.30 - 0.225 - 0.105 = 0.07 moles.

Then, in the bottom stream, we will locate the moles of benzene, toluene, and xylene.

Benzene moles in the first column's bottom stream: 0.30 - 0.225 = 0.075 moles.

Moles of toluene in the first column's bottom stream equal 0.35 moles.

Moles of xylene in the first column's bottom stream are equal to 0.225 moles (0.30 + 0.35 + 0.075).

By converting these mole fractions to percentages, we can finally:

Toluene is 0.538 times 100 and xylene is 0.436 times 100, giving a total of 2.56% for benzene and 0.538 for toluene.

As a result, 2.56% benzene, 53.8% toluene, and 43.6% xylene make up the bottom stream from the second column's molar composition.

To learn more about Molar mass refer to:

brainly.com/question/837939

#SPJ4

The option that will support the attackers' plan is Command & Control Computer Bots.

A 'bot' is known to be a short term for the word robot. It is regarded as a software program that carries out automated work and is often used to  replace human user behavior.

Note that when An attacker is planning to set up a backdoor that will infect a set of specific computers at an organization, to inflict a set of other intrusion attacks remotely, the option that will support the attackers' plan is Command & Control Computer Bots.

Learn more about Computer Bots from

https://brainly.com/question/13678620

#SPJ1

The key factor that has contributed to the growth and popularity of big data is the implosion in data growth.

The growth and popularity of big data can be largely attributed to the implosion in data growth. The continuous advancement of technology, particularly mobile and wireless technology, has led to an exponential increase in the amount of data being generated and collected.

Mobile devices, such as smartphones and tablets, have become ubiquitous in today's society, enabling people to create and consume vast amounts of data on a daily basis. These devices are equipped with various sensors, cameras, and applications that generate data related to users' activities, preferences, locations, and more. Additionally, the widespread adoption of wireless connectivity has made it easier to capture and transmit data in real-time.

The implosion in data growth has revolutionized the way organizations operate and make decisions. The availability of large volumes of data has opened up new possibilities for data-driven insights, predictive analytics, and business intelligence. Companies can now analyze vast datasets to uncover patterns, trends, and correlations that were previously hidden. This has led to improvements in customer experiences, targeted marketing strategies, operational efficiencies, and innovation in various industries.

In summary, the implosion in data growth, driven by mobile and wireless technology, has played a significant role in the growth and popularity of big data, enabling organizations to harness the power of data for decision-making and competitive advantage.

Learn more about  technology here: https://brainly.com/question/11447838

#SPJ11

By using the binomial probability formula, the probability of at least two 3's is equal to 0.1319.

Since the fair cubical die is thrown four times, the number of times is given by n = 4 and the probability of 3's is P = 1/6.

Mathematically, the binomial probability formula is given by:

\(P(X \geq x) =\sum^{n}_{r=x} ^nC_r (p)^r (q)^{(n-r)}\\\\P(X \geq 2) = \; ^4C_2 (\frac{1}{6} )^2 (\frac{5}{6} )^{(4-2)} + ^4C_3 (\frac{1}{6} )^3 (\frac{5}{6} )^{(4-3)} + ^4C_4 (\frac{1}{6} )^4 (\frac{5}{6} )^{(4-4)}\\\\P(X \geq 2) = 6 \times \frac{1}{36} \times \frac{25}{36} + 4 \times \frac{1}{216} \times \frac{5}{36} + 1 \times \frac{1}{1296} \times 1\\\\P(X \geq 2) = \frac{150}{1296} + \frac{20}{1296}+ \frac{1}{1296}\)

P(X ≥ 2) = 19/144

P(X ≥ 2) = 0.1319.

Read more on probability here: https://brainly.com/question/25870256

#SPJ1

h = 129.2m

Pressure at depth is equal to denstiy of the fluid times the acceleartion due to gravity times the depth:

P = pgh

density at the surface of the ocean is at .101MPa

Take the pressure subtract the pressure due to atmosphere:

1.4 - .101 = 1.299 MPa

1299000 Pa = 1025kg/m^3 * 9.8m/s^2 * h

h = 129.2m

you can learn more through link below:

https://brainly.com/question/14356467#SPJ4

Platinum filament.

Thomas Edison went through a series of different experiments while developing bulb until and unless the electricity passed through the Platinum filament, and it finally worked.

You can learn more about Bulb development through the link below:

https://brainly.com/question/14016925#SPJ4

Dialogue must be very concise or succinct in order to best offer the reader bite-size information that will propel the story along.

In storytelling, dialogue serves multiple purposes, including conveying information, developing characters, and advancing the plot. By keeping the dialogue concise, the writer can deliver essential information efficiently, without overwhelming the reader with excessive details or unnecessary conversation. Bite-size dialogue allows for a faster pace and keeps the reader engaged, as they receive crucial information in a digestible manner. It also helps maintain the flow of the story by avoiding long-winded conversations that may slow down the narrative. Concise dialogue ensures that every word counts and serves a purpose, enhancing the overall impact of the story.

learn more about concise here :

https://brainly.com/question/23269175

#SPJ11

Answer:

The final velocity of the rocket is 450 m/s.

Explanation:

Given;

initial velocity of the rocket, u = 0

constant upward acceleration of the rocket, a = 18 m/s²

time of motion of the rocket, t = 25 s

The final velocity of the rocket is calculated with the following kinematic equation;

v = u + at

where;

v is the final velocity of the rocket after 25 s

Substitute the given values in the equation above;

v = 0 + 18 x 25

v = 450 m/s

Therefore, the final velocity of the rocket is 450 m/s.

Answer:

System analysis can be defined as a deep analysis of a part of the structure of a module that has been designed before. System design means to make any module or a part of the structure from scratch and build it completely without estimation.

Explanation:

Two technicians are discussing solder repair. Technician A says that solder should be applied to the soldering iron tip while soldering Technician B says that the solder should be applied to the wire joint while soldering. The correction technician is: "Both Technician A and B (Option C)

Soldering is a joining method that uses solder to bind several metals together. Solder is a metal alloy typically composed of tin and lead that is melted using a hot iron.

The iron is heated to a temperature above 600 degrees Fahrenheit before cooling to form a strong electrical connection. To put it another way, soldering is the process of uniting metal pieces to produce a mechanical or electrical link.

It commonly employs a low melting point metal alloy (solder), which is heated and applied to the metal pieces to be connected, and when the solder solidifies, it attaches to the metal parts and makes a connection.

Learn more about soldering:
https://brainly.com/question/28555395

#SPJ1

Full Question:

Two technicians are discussing solder repair. Technician A says that solder should be applied to the soldering iron tip while soldering Technician B says that the solder should be applied to the wire joint while soldering. Who is Correct?

Answer:

International Film Festival

Judging the best best film:

a. The probability that out of five judges (random sample),  three are in favor of film FA is:

= 33%.

b. The demerits of classical probability are:

1. Classical probability can only be used with events that have definite numbers of possible outcomes.  

2. Classical probability can only handle events where each outcome is equally likely.

3. Classical probability is based on the assumption of linear relationship (which is not always true in real life) between the latent variable and observed scores.

Explanation:

a) Number of judges = 11

Number of judges in favor of FA film = 6

Number of judges in favor of FB film = 5

Probability of judges in favor of FA film = 6/11

Probability of judges in favor of FB film = 5/11

Random sample of judges = 5

Probability that out of five judges, three are in favor of film FA = 3/5 * 6/11

= 18/55

= 33%

b) Classical probability is the simple probability showing that each event has equal chance of happening.  It can be contrasted with empirical probability that is obtained from experiments.

In HTML, the attribute used to specify that an input field must be filled out is "required" (option A). This attribute ensures that the user must provide a value for the input field before submitting the form, promoting proper form completion and data validation.

If the required attribute is not satisfied, the form will not be submitted, and the user will receive a prompt to fill in the necessary information. The attribute used to specify that an input field must be filled out in HTML is the "required" attribute. This attribute is used in conjunction with the "input" tag to indicate that the user must fill out the specified field before submitting the form. When the user tries to submit the form without filling out the required field, an error message will appear prompting them to fill out the required field. The "validate" and "mandatory" attributes are not used in HTML to achieve this functionality. While the term "input_required" could potentially be used as a custom attribute, it is not a standard attribute in HTML. Therefore, the correct answer is A) required.

Learn more about HTML here

https://brainly.com/question/28546434

#SPJ11

The service tool C and D terminals are connected to the IT terminal board.

What is terminal?

A terminal is the endpoint of a conductor from a component, device, or network. Terminal may also refer to an electrical connector at this endpoint that serves as a reusable interface to a conductor and provides a point for external circuits to be attached. A termination can be as simple as the end of a wire or as complex as a connection or fastener. In network analysis, a terminal is a theoretical location at which connections to a network can be created and does not necessarily refer to any real item. It is sometimes referred to as a pole in this context, particularly in older publications. Terminals for external connections are represented on circuit diagrams by empty circles.

To learn more about terminal
https://brainly.com/question/4455094

#SPJ9

Answer:

a) 42.422 KN

b) 44.356 KN

Explanation:

Given data :

Diameter = 20 mm

yield strength = 350 MN/m^2

Torque ( T )  = 100 N.m

Bending moment = 150 N.m

Determine the value of the applied axial tensile force when yielding of rod occurs

first we will calculate the shear stress and normal stress

shear stress ( г ) = Tr / J = [( 100 * 10^3)  * 10 ]  /  \(\pi /32\) * ( 20)^4  

                                       = 63.662 MPa

Normal stress(  Гb + Гa )  = MY/ I  +  P/A

= [( 150 * 10^3)  * 10 ]  /  \(\pi /32\) * ( 20)^4   + 4P / \(\pi * 20^2\)

= 190.9859 + 4P / \(\pi * 20^2\)  MPa

a) Using MSS theory

value of axial force = 42.422 KN

solution attached below

b) Using MDE  theory

value of axial force = 44.356 KN

solution attached below

Answer:

no idea

Explanation:

gvghvvvghhbbgggggggig gjgjg gjgbg gig gg bg GB g GB GB GB GB g GB GB GB of me and I am a diary and crewmate hide if you see a diary or not the other person is a non-electrolyte or no one vent the imposter win a diary or you can get any more confidently than you are in a spectacular place is the most important points to be mo to get skins and crewmate for a few days to be sure it will be the same for me it will take a while for a couple to get the right angle bu the other one is come to the end and then you have birds to get a lot more than a diary of a candle or no other one in a few weeks or no time to do it for me and my friend who has no idea how much time I have been to a new episodes and the best of all the time I am going sleep

To plot the results of the survey as a pie chart in MATLAB, you can use the "pie" function.

First, you'll need to create a vector of the number of students who like each type of ice cream. You can do this by subtracting the number of students who like vanilla and chocolate from the total number of students:
```matlab
num_strawberry = 24 - 11 - 6;
```
Then, you can create a vector of the data you want to plot:
```matlab
data = [11 6 num_strawberry];
```
Next, you can create a cell array of labels for the different types of ice cream:
```matlab
labels = {'Vanilla', 'Chocolate', 'Strawberry'};
```
Now you can plot the pie chart using the "pie" function:
```matlab
pie(data, labels);
```
This will create a pie chart with the labels and data you specified. Finally, you can add a title to the plot using the "title" function:
```matlab
title('Ice Cream Preferences');
```

To know more about vector visit:-

https://brainly.com/question/21157328

#SPJ11

1. The number of communication network hops is 6, and the worst-case remote communication cost in a hypercube topology is 160 ns

2. The CPI for the application in the grid topology is 0.54

3. Thhe ring topology has the highest performance improvement, with a 84% increase in performance when compared to the case where remote communication is used.

1. The number of communication network hops is 6, and the worst-case remote communication cost in a hypercube topology is:

100 + 10h = 100 + 10 x 6 = 160 ns

2. In the case of the grid topology, the worst-case remote communication cost is 240 ns, so the CPI for the application in the grid topology is:

= 0.5 + (0.2/100) x 240 = 0.54

In the case of the hypercube topology, the worst-case remote communication cost is 160 ns, so the CPI for the application in the hypercube topology is:

= 0.5 + (0.2/100) x 160 = 0.54

3. For the ring topology:

Performance improvement_ring = (0.92 - 0.5) / 0.5 x 100% = 84%

For the grid topology:

Performance improvement_grid = (0.54 - 0.5) / 0.5 x 100% = 8%

For the hypercube topology:

Performance improvement_hypercube = (0.54 - 0.5) / 0.5 x 100% = 8%

Thus, the ring topology has the highest performance improvement, with a 84% increase in performance when compared to the case where remote communication is used.

Learn more about communication on

https://brainly.com/question/28153246

#SPJ4

Water pressure principles is known to  state that the amount of Fluid pressure is said to be perpendicular to the surface on which it it exert or works on.

Note that  principle is shown by a vessel that is said to be having flat sides and has water. The pressure exerted by the weight of the water is therefore known to be perpendicular to the walls of the storage.

A water butt is known to be a container that is made and also used to store a lot of rainwater.

Note that Water pressure principles is known to  state that the amount of Fluid pressure is said to be perpendicular to the surface on which it it exert or works on.

Learn more about Water pressure principles  from

https://brainly.com/question/14813457

#SPJ1

Answer:

Cool.

Explanation:

The statement "a bot propagates itself and activates itself, whereas a worm is initially controlled from some central facility" is FALSE.

Explanation: A computer virus is a program that replicates itself by modifying other programs and adding its own code. A worm is a self-replicating program that spreads through networks. Both a worm and a bot are malware (malicious software).But there are differences between a worm and a bot. A bot is a program that runs automatically, executing tasks over the internet. A bot can be used for good or evil purposes, depending on the intent of the person who created it. A botnet is a group of computers that have been compromised by a hacker or malware. A botnet can be used to launch cyberattacks, distribute spam, or steal information. A worm is a program that spreads itself automatically from one computer to another. A worm can cause damage to a computer network by consuming bandwidth, deleting files, or changing settings. In short, the statement "a bot propagates itself and activates itself, whereas a worm is initially controlled from some central facility" is false.

To know more about Bot propagates visit:

https://brainly.com/question/32320794

#SPJ11

Therefore, we can design the circuit using two 2:1 multiplexers as a two-bit adder under the given conditions.

Yes, I can design the circuit using the given conditions. Here are the details of the work:

Truth Table:

Let's use A and B as inputs, S as sum, and C as the carry. The truth table is given below:

A B S C0 0 0 00 1 1 00 1 0 11 0 1 01 1 0 1

Simplification K-Map/Implementation Table

:From the truth table, we can get the following equations:

S = A'BC' + AB'C + ABC' + ABC = AB + AC + BC'

Implementation table is given below:

AB C S000010011001101111

Logic Circuit:

We can use the two available 2:1 multiplexers to implement the circuit. Here is the logic circuit diagram:

Therefore, we can design the circuit using two 2:1 multiplexers as a two-bit adder under the given conditions.

To know more about multiplexers visit:

https://brainly.com/question/15052768

#SPJ11

Answer:

electric circuit, a conduit for moving current. A battery or generator, a device that provides energy to the charged particles that make up the current, a device that uses current, such as a lamp, an electric motor, or a computer, and the connecting wires or transmission lines make up an electric circuit. Ohm's law and Kirchhoff's rules are two fundamental laws that quantitatively define how electric circuits function.

network in series

circuit parallel

There are various categories in which to place electric circuits. Only one direction of current can flow through a direct-current circuit. As in most residential circuits, an alternating-current circuit transports current that pulses back and forth repeatedly every second. (To learn more about direct and alternating current circuits, visit electricity: Direct electric

Explanation:

is this good? please mark brainliest

Answer:

Explanation:

On the basis of this information, we are going to compute the engineering stress necessary to produce an engineering strain of 0.28.

For clarity and you will find the solving in the attached file for your reference.

should you need further information do let me know.

​  

A broken yellow line on the pavement tells that the adjacent lane is traveling in the opposite direction and passing is permitted.

A broken white line on the pavement show that the adjacent lane is traveling in the same direction and passing is permitted.

Pavement markings are known to be tools that are used to pass infor or messages to roadway users.

Note  that they tell the part of the road that one need to use, give information about conditions ahead, and others

Note that A broken yellow line on the pavement tells that the adjacent lane is traveling in the opposite direction and passing is permitted.

Learn more about pavement markings from

https://brainly.com/question/10179521

#SPJ1

The available options are:

a. Want for a television set

b. Want for medical attention

c. Want for friendship

d. Want for new clothing

Answer:

Want for friendship

Explanation:

Given that economic want is what humans desire to have or possess such that they pay money to acquire them.

Hence, from the available options "want for friendship " is not economic want because it can't be bought with money, while other options can be bought with money or monetary transaction.

Answer:

When traveling at higher speeds (40 mph or faster), the most fuel-efficient way to keep the car cool is to follow these tips:

1. Use the vehicle's ventilation system: Instead of relying on air conditioning, use the car's ventilation system to circulate fresh air from outside. This helps to cool down the interior without putting extra load on the engine, thus saving fuel.

2. Close windows and sunroofs: To reduce wind resistance and drag, close all windows and sunroofs while driving at higher speeds. Open windows create drag, which can increase fuel consumption.

3. Park in the shade: Whenever possible, park your car in a shaded area to avoid excessive heating when it's not in use. This can help keep the car cooler and reduce the need for extra cooling when you start driving.

4. Use reflective sunshades or window tinting: Use reflective sunshades on your windshield and window tinting on side windows to reduce the amount of heat entering the car. This can help keep the interior cooler, reducing the need for excessive cooling while driving.

5. Maintain your vehicle: Regular maintenance, such as checking and replacing coolant, inspecting the radiator, and ensuring proper functioning of the engine cooling system, can help keep your car running efficiently and prevent overheating.

6. Plan your trips strategically: If possible, try to avoid driving during the hottest part of the day. By planning your trips to avoid peak temperatures, you can reduce the strain on your vehicle's cooling system and minimize the need for excessive cooling.

Remember that these tips are specifically focused on keeping the car cool while maintaining fuel efficiency at higher speeds. In certain circumstances, such as extremely hot weather, using the air conditioning sparingly may be necessary for passenger comfort, but it will increase fuel consumption.